Peripherals
This article describes supported add-on peripherals for RouterBOARD hardware devices.
Cellular modems
RouterOS v7 supports the following cellular modems:
- MikroTik modems.
- Third-party modems supported by device class/type:
- MBIM class USB interface
- USB-CDC class USB interface
- RNDIS type USB interface
- Third-party modems with added support (see the modem table below).
Please note
- Not all modems are listed in the supported modem table. Some modems may work even if not listed because modem manufacturers often re-use the same hardware IDs, and vice versa.
- Customized, localized, or locked units may have compatibility issues.
- Third-party modems may require configuration adjustments before they can be used with RouterOS.
- For mini-PCIe modems with a USB3.0 interface installed in a mini-PCIe slot with PCIe/USB2.0 support, the USB speed must be limited to USB2.0, or the mini-PCIe shared PCIe/USB3.0 pin must be isolated. See the picture below the table.
Cellular modems
| Model | vendor-id | device-id | Tested RouterOS version | Comments | Format |
|---|---|---|---|---|---|
| Alcatel IK40 | v6.41RC11 | LTE interface, Modem can be configured only through modem's configuration WEB page. | USB | ||
| Alcatel IK41 | v6.48 | Config-less LTE interface | USB | ||
| Android usb tethering interface | v6.7 | Some settings are ignored. | USB | ||
| AnyData ADU-E630WH | v6 | ( aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A") | USB | ||
| Anteniti 3372h-153 | 7.12 | USB | |||
| BandRich C501 | v5.25 and v6.0 | USB | |||
| Cinterion LTE Modem | 0x1e2d | 0x0061 | v7.14 and higher | LTE interface, some settings are ignored. Not full SMS functionality. | MiniPCI-e |
| D-link DWM-157 | 0x2001 | 0x7d02 | v6.xx | Works! Data Channel: 2, Info Channel: 3, Modem Init: AT+CFUN=1, vendor-id="0x2001" device-id="0x7d02" Some info from modem: > H/W Ver.: B1, F/W Ver.: 2.0.1eu, revision: +CGMR: MOLY.WR8.W1231.DC.WG.MP.V3, 2013/04/09 02:08 Different HW revisions might not work with RouterOS | USB |
| D-link DWM-222 | See comments | Multiple modem versions with the same marketing name exist: H/W ver: A1 - supported as config-less LTE interface from RoS v6.38Modem firmware version starting from "2.1.4EU".H/W ver: A3 - works as config-less LTE using modem firmware provided RNDIS interface (RouterOS v7 only) | USB | ||
| Dell DW5821e | v7.4beta4 and higher | MBIM driver. Revision: T77W968.F1.0.0.5.2.VZ.013 044 | M.2 | ||
| Dell DW5821e-eSIM | 0x413c | 0x81e0 | 7.11 and higher | MBIM driver. FW: T77W968.F1.0.0.5.2.GC.013. "at-chat" support added | M.2 |
| DELL T99W175 | 0x05c6 | 0x90d5 | 7.16 and higher | MBIM driver. FW: T99W175.F0.1.0.0.9.GC.004. "at-chat" support added | M.2 |
| Dell Wireless 5530 HSPA | v6.1 and higher | Data channel 0, Info channel 0, init: AT+CFUN=1 (needs to manually change profile by command AT*ENAP=1,1) | MiniPCI-e | ||
| Ericsson F5521gw | v6.x and higher | MiniPCI-e | |||
| Fibocom FM150-AE/FM150-NA | 0x2cb7 | 0x0111 | v7.1beta5 | MBIM driver. Revision: 89603.1000.00.01.01.03 | M.2 |
| Fibocom NL-952-EAU | v7.1beta5 | MBIM driver. Revision: 19600.7000.00.04.01.05 | M.2 | ||
| Marvell PXA1802 based modems | 0x1286 | 0x4e31 | v7.2.2 | mini-PCIe | |
| Huawei E153 | v6.31 and higher | USB | |||
| Huawei E171 | v6.xx | Works! ppp interface, vendorid=0x12d1 deviceid=0x140c | USB | ||
| Huawei e3131 | v6.xx and higher | ppp interface | USB | ||
| Huawei E3372h, E5576h, E8372h | 0x12d1 | 0x14db | v6.8 | Config-less LTE interface for modems with vendor-id="0x12d1" device-id="0x14db" Models with suffixes -320 and -608 will not work with RouterOS v6, please use v7 instead Models with suffixes -325 work only with arm cpu | USB |
| Huawei E3276-150 | v6.xx | ppp interface | USB | ||
| Huawei E3351 | v6.24 and higher | USB | |||
| Huawei E3531 | v6.24 or 6.40RC25 | There are different versions of this modem E3531-6 works from version 6.40RC25 as ppp, mbim is supported only from RouterOS V7 | USB | ||
| Huawei e398 | v6.xx and higher | ppp interface | USB | ||
| Huawei E5377 | v6.36.1 | MIFI unit. No serial support, but works with IP on LTE interface | USB | ||
| Huawei E5673s-609 | v6.xx | LTE interface | USB | ||
| Huawei K5160 | v6.37 v7.0beta6 | v6 and v7 - config-less LTE interface v7 - by default will try to use the modem in MBIM mode | USB | ||
| Huawei K5161 | v6.47 | Config-less LTE interface | USB | ||
| Huawei ME909s-120 | v6.28 | Recommended modem firmware version 11.617.24.00.00. To reduce LTE interface IP subnet mask to /32 configure modem with at-chat command: /interface/lte/at-chat [find] input="AT^CUSTFEATURE=3,1" |
MiniPCI-e | ||
| Huawei ME909u-521 | v6.11 | MiniPCI-e | |||
| Huawei MU609 | v6.11 | MiniPCI-e | |||
| Huawei MU709s-2 | v6.28 | MiniPCI-e | |||
| Huawei MS2372h-517 | v7.12beta3 | ppp/serial interface | USB | ||
| Jaton MT421e | v6.40RC32 | LTE interface with Ethernet emulation (no configuration possible), LTE supported bands 42/43 | MiniPCI-e | ||
| Netgear Unite Explore 815S | v6.41 | MIFI unit. No serial support, but works with IP on LTE interface. | USB | ||
| Novatel USB730L | v6.41RC6 | LTE interface | USB | ||
| Olivetti Olicard 500 | v6.41RC11 | ppp interface | USB | ||
| Quectel EC20/EC21 | v6.xx | ppp interface | MiniPCI-e | ||
| Quectel BG77 | 0x2c7c | 0x0700 | v6.47 | Serial/PPP interface, single AT/modem channel | OEM module |
| Quectel BG95-M3 | v6.47 | Serial/PPP interface, single AT/modem channel Will not work on wAP R ac boards. | mini-PCIe | ||
| Quectel BG96 | v6.45 | Serial/PPP interface, 2x AT/modem channels | mini-PCIe | ||
| Quectel EC25-EU | 0x2c7c | 0x0125 | v6.42 | ppp/LTE interface. RouterOS v6 CDC-ECM mode - LTE interface receive address in modem's internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. | MiniPCI-e |
| Quectel EG25-G | 0x2c7c | 0x0125 | 6.48.3 | RouterOS v6 CDC-ECM mode - LTE interface receive address in modems internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. On some boards it may be required to disable SIM hot plug detection: /interface/lte/set [find] modem-init="AT+QSIMDET=0,1" |
MiniPCI-e |
| Quectel EM12-G | 0x2c7c | 0x0512 | v7.1beta5 | MBIM driver | m.2 |
| Quectel EP06 | v6.42 | ppp/LTE interface | MiniPCI-e | ||
| Quectel RG255C-GL | v7.18 | Basic support with at-chat, minimum firmware revision: RG255CGLABR01A04M4G_A0.004.A0.004 Modem composition: at+qcfg="usbnet",0 |
mini-PCIe | ||
| Quectel RM500Q-GL | 0x2c7c | 0x0800 | v7.1beta6 | MBIM driver | m.2 |
| Quectel RM500Q-AE | 0x2c7c | 0x0800 | v7.1beta6 | MBIM driver | m.2 |
| Quectel RM502Q-AE | 0x2c7c | 0x0800 | v7.1beta5 | MBIM driver | m.2 |
| Quectel RM510Q-GL | 0x2c7c | 0x0800 | 7.9 | MBIM driver | m.2 |
| Quectel UC15 | v6.xx | Works, ppp interface | MiniPCI-e | ||
| Quectel UC20 | v6.xx | Works, ppp interface | MiniPCI-e | ||
| R11e-4G | 0x2cd2 | 0x0003 | v6.42 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e |
| R11e-LTE6 | 0x2cd2 | 0x0004 | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e |
| R11e-LTE | 0x2cd2 | 0x0001 | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e |
| Sierra Netgear AirCard 320U | 6.41 | Customer tested the modem with firmware 03.05.23 | USB | ||
| Sierra wireless MC73xx | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface with the modem switched to expose the MBIM interface. MC7304 tested with firmware SWI9X15C_05.05.67.00 | MiniPCI-e | ||
| Sierra Wireless MC7430 | v6.xx and higher | Data channel 2, Info channel 2, Modem init: AT+CGATT=0, Dial-command: AT+CGATT=1;D*99#, also needs 3.0 pins isolated (PINS:23,25,27,31,33) | MiniPCI-e | ||
| Sierra Wireless MC74xx | v7.1 | Basic functionality support for modems with MBIM interface/USB composition | mini-PCIe | ||
| Sierra Wireless MC7455 | v7.3beta37 | MBIM mode with extended support for USB compositions: 1009 - diag,modem,mbim100D - diag,nmea,modem,mbim | mini-PCIe | ||
| Sierra Wireless MC7710/MC7700/MC7750 | v5.25, v6.0 and 6.40RC43 | If the modem uses firmware 3.5 it should be upgraded to 3.5.23.2 firmware release in order to work in RouterOS correctly again. | MiniPCI-e | ||
| SIMcom SIM5360 | v6.xx | Works! Using PPP interface, vendor-id="0x05c6" device-id="0x9000" | MiniPCI-e / USB w/ converter | ||
| SIMcom SIM7100 | 0x1e0e | 0x9001 | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. | MiniPCI-e / USB w/ converter |
| SIMCom SIM8202G-M.2 | v7.11 | MBIM driver supported: AT+CUSBCFG=usbid,1e0e,901e | m.2 | ||
| SXT LTE | v6 | LTE interface. Old version of SXT LTE | Built-in | ||
| Tele2.ru LTE-D402 | v6.47 | Config-less LTE interface | |||
| Telecom NZ T-Stick ZTE MF-181 | v6.0rc13 | Data Channel=2, Info Channel=2, APN internet.telecom.co.nz, PHONE=*99#. Tested ok for both data and SMS on CCR1016-12G | USB | ||
| Telit FN980m | v7.5 | AT#USBCFG=2 | m.2 | ||
| Telit LE910 | 0x1bc7 | 0x1201 | v6.xx | ppp interface | MiniPCI-e |
| Telit LE910C1 | v6.46 | Non-configurable from RouterOS | MiniPCI-e | ||
| Telit LM940 | v6.44 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | ||
| Telit LM960 | v6.46 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | ||
| TPS (Turning Point Solution) GCT450 | v6.48 | Config-less LTE interface | MiniPCI-e | ||
| Vodafone (Huawei) K4203 | v7.xx | Not supported in ROS v6, but as this modem supports MBIM driver support will be possible in ROS v7. | USB | ||
| Vodafone K4201-Z | v6.8 | Some settings are ignored. LTE interface. | USB | ||
| Vodafone K4305 | v6.7 | Some settings are ignored. | USB | ||
| Vodafone K5160 | v6.37 | Some settings are ignored. | USB | ||
| Yota LU150 | v5.22 and v6.4 | Some settings are ignored. | USB | ||
| Yota wifi modem | v6.7 | Some settings are ignored. | USB | ||
| Yota WLTUBA-107 | v6.0 | Some settings are ignored. | USB | ||
| ZTE 821D | v6.x | Set Info channel = 1, Data channel = 3, Dial command=ATDT | USB | ||
| ZTE AC5730 | v6.x | USB | |||
| ZTE ME3630-E | v6.40RC26 | ppp and LTE interface | MiniPCI-e | ||
| ZTE MF110 | v6.28 and higher | Set info channel = 2, data channel = 2, Dial command=ATM1L3DT | USB | ||
| ZTE MF823 | v6.8 | Some settings are ignored. For some devices it's needed to enter FACTORY mode to change operating state. | USB | ||
| ZTE MF825A | v6.xx | Some settings are ignored. | USB | ||
| ZTE MF827 | v6.8 | Some settings are ignored. | USB | ||
| ZTE MF832S | v7.10 | Config-less support, may require to set some settings using at-chat or modem init string | USB | ||
| ZTE MF833U1 | 0x19d2 | 0x1405 | v7.20.6 | Config-less LTE interface | USB |
| ZTE MF90 | v6.44beta32 and higher | LTE interface | USB |
Warning Not all modems are listed. Localized and locked units may have compatibility issues.
For some modems with USB3.0 support in some cases USB3.0 pins need to be isolated to ensure correct initialization:
SFP modules
| Brand | Model | Rate | Connector/Cable type | Wavelength | Tested with | Works / Doesn't |
|---|---|---|---|---|---|---|
| MikroTik | S-85DLC05D | 1,25G | Dual LC, MM | 850nm | *Check: SFP/SFP+ compatibility reference table | Natively supported |
| MikroTik | S-31DLC20D | 1,25G | Dual LC, SM | 1310nm | *Check: SFP/SFP+ compatibility reference table | Natively supported |
| MikroTik | S-35LC20D | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1550nm | *Check: SFP/SFP+ compatibility reference table | Natively supported |
| MikroTik | S-53LC20D | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1310nm | *Check: SFP/SFP+ compatibility reference table | Natively supported |
| MikroTik | S-RJ01 | 1000/100/10 | RJ45, Cat5/Cat6 | N/A | *Check: SFP/SFP+ compatibility reference table | Natively supported |
| Axiom | AXG91632 | 1000BASE-LX | Dual LC | 1310nm | CRS125-24G-1S-RM | Works! |
| Finisar | FCLF-8521-3 | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| Finisar | FCLF-8521-3-MD | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| Finisar | FTRJ8519P1BNL-B1 | 10/100/1000 1.25 Gb/s 1000Base-SX Ethernet | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| Finisar | FTLF8519P2BNL | 10/100/1000 1.25 Gb/s 1000Base-SX Ethernet | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| Finisar | FTRJ1319P1BTL | 1.25Gb/s 1000Base-LX Ethernet | Dual LC, SM | 1310nm | CCR1009-8G-1S-1S+ and CCR1009-7G-1C-1S+ | Works! |
| Unica | SFP-1.25G-T | 1000M | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| Dell | FTLX8571D3BCL | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| Unica | GP-3124-L2CD-C | 1,25G | Dual LC, MM | 1310nm | RB2011LS-IN | Works! |
| Cisco | GLC-T | 1.25G | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| Cisco | GLC-SX-MM | 1000BASE-SX SFP transceiver module for MMF, 1.25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| Cisco | SFP-GE-L | 1000BASE-LX/LH SFP transceiver module for SMF, 1.25G | Dual LC, SM | 1300nm | Various MT hardware | Works! |
| 6COM | 6C-SFP-T | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| 6COM | 6C-WDM-0210BSD | 1,25G | BiDi SC, SM | Tx:1550nm/Rx:1310nm | RB2011LS-IN | Works! |
| 6COM | 6C-WDM-0210ASD | 1,25G | BiDi SC, SM | Tx:1310nm/Rx:1550nm | RB2011LS-IN | Works! |
| 6COM | 6C-SFP-0310D | 1,25G | Dual LC, MM | 1310nm | RB2011LS-IN | Works! |
| 6COM | 6C-SFP-0301D | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| Ingellen | INSP-T(10/100/1000) | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| Ingellen | INSPL-53-BX | 1,25G | BiDi LC, MM | 1550/1310 | RB2011LS-IN | Works! |
| Ingellen | INSPL-35-BX | 1,25G | BiDi LC, MM | 1310/1550 | RB2011LS-IN | Works! |
| Ingellen | INSP-LX-SM | 1,25G | Dual LC, SM | 1310nm | RB2011LS-IN | Works! |
| Ingellen | INSP-SX-MM | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| AXCEN | AXGT-R1T4-05I1 | 10/100/1000 | RJ45, Cat6 | N/A | RB2011LS-IN | Works! |
| AXCEN | AXGD-37А4-0531 | 1,25G | BiDi LC, MM | Tx:1550nm/Rx:1310nm | RB2011LS-IN | Works! |
| AXCEN | AXGD-16А4-0531 | 1,25G | BiDi LC, MM | Tx:1310nm/Rx:1550nm | RB2011LS-IN | Works! |
| AXCEN | AXGD-1354-0531 | 1,25G | Dual LC, MM | 1310nm | RB2011LS-IN | Works! |
| AXCEN | AXGD-5854-0511 | 1,25G | Dual LC, MM | 850nm | RB2011LS-IN | Works! |
| TP-Link | TL-SM311LS | 1,25G | Dual LC, SM | 1310nm | RB2011LS-IN | Works! |
| TP-Link | TL-SM311LM | 1,25G | Dual LC, MM | 850nm | CCR1036 12G-4S | Works! |
| OPTIC | OPTIC-SFP-3524S-02-SC | 1,25G | BiDi SC, SM | Tx:1310nm/Rx:1550nm | RB2011UAS-RM, RB260GS | Works! |
| OPTIC | OPTIC-SFP-5324S-02-SC | 1,25G | BiDi SC, SM | Tx:1550nm/Rx:1310nm | RB2011UAS-RM, RB260GS | Works! |
| OPTIC | OPTIC-SFP-S1203-L3302-LC | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1550nm | RB2011UAS-RM, RB260GS | Works! |
| OPTIC | OPTIC-SFP-S1205-L3302-LC | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1310nm | RB2011UAS-RM, RB260GS | Works! |
| ROBOFiber | SFP-7120-55 | 1,25G | Dual LC, SM | 1550nm | CCR1036-12G-4S, RB2011 | Works! |
| ROBOFiber | SFP-7120-WA | 1,25G | BiDi LC, MM | Tx:1490nm/Rx:1550nm | CCR, RB2011 | Works! |
| ROBOFiber | SFP-7120-WB | 1,25G | BiDi LC, MM | Tx:1550nm/Rx:1490nm | CCR, RB2011 | Works! |
| Enguity | SFP-3647603KM.b1310 XT | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1550nm | CCR, RB2011, RB260GS | Works! |
| Enguity | SFP-3647603KM.b1550 XT | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1310nm | CCR, RB2011, RB260GS | Works! |
| Enguity | SFP-3647610KM.b1490 XT | 1,25G | BiDi LC, SM | Tx:1490nm/Rx:1550nm | CCR, RB2011, RB260GS | Works! |
| Enguity | SFP-3647610KM.b1550 XT | 1,25G | BiDi LC, SM | Tx:1550nm/Rx:1490nm | CCR, RB2011, RB260GS | Works! |
| AdvOptics MSA | GLC-SX-MM | 1,25G | BiDi LC, MM | Tx:1310nm/Rx:1310nm | CCR, RB2011, RB260GS | Works! |
| AdvOptics MSA | GLC-ZX-SM | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1310nm | CCR, RB2011, RB260GS | Works! |
| Proline | GLC-BX-D20-PRO | 1,25G | BiDi LC, SM | Tx:1490nm/Rx:1310nm | CRS125 | Works! |
| Proline | GLC-BX-D40-PRO | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1490nm | CRS125 | Works! |
| Foundry Networks | E1MG-BXU-AC | 1,25G | BiDi LC, SM | Tx:1310nm/Rx:1490nm | RB3011UiAS, hAP ac | Works! |
| Avago | SFBR-5799APZ | 1,25G | Dual LC, MM | 850nm | CRS326, CRS112 | Works in 1Gbps mode! |
| Eltex | NTU-SFP-100 | 1,25G | SC | N/A | RB4011iGS+ | Works! |
SFP+ modules
| Brand | Model | Distance | Rate | Connector/Cable type | Wavelength | Tested with | Works / Doesn't |
|---|---|---|---|---|---|---|---|
| MikroTik | S+85DLC03D | 300m | 10G | Dual LC, MM | 850nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported |
| MikroTik | S+31DLC10D | 10km | 10G | Dual LC, SM | 1310nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported |
| MikroTik | S+23LC10D | 10km | 10G | BiDi LC, SM | Tx:1270nm/Rx:1330nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported |
| MikroTik | S+32LC10D | 10km | 10G | BiDi LC, SM | Tx:1330nm/Rx:1270nm | All MikroTik products with SFP/SFP+ interfaces | Natively supported |
| MikroTik | S+DA0001 | 1m | 10G | Twinax Copper | N/A | All MikroTik products with SFP/SFP+ interfaces | Natively supported |
| MikroTik | S+DA0003 | 3m | 10G | Twinax Copper | N/A | All MikroTik products with SFP/SFP+ interfaces | Natively supported |
| MikroTik | S+RJ10 | various, depending on link rate. Check brochure for more details | 10G/5G/2.5G/1G/100M/10M | RJ45 - Cat5E/Cat6/Cat7 | N/A | All MikroTik products with SFP+ interfaces | Natively supported |
| Atop | APSP55B30CDL40 | 40km | 10G | Dual LC, SM | 1550nm | CRS series, CCR series devices with SFP+ interfaces | Does NOT work! |
| Cisco | SFP-10G-LR | 10km | 10G | Dual LC, SM | 1310nm | RB2011LS-IN | Works! |
| Dell (Finisar) | FTLX8571D3BCL | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! |
| Juniper (Finisar) | FTLX8571D3BCL-J1 | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! |
| Intel (Finisar) | FTLX8571D3BCV-IT | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! |
| OEM (Juniper?) | EX-SFP-10GE-SR-OEM | 300m | 10G | Dual LC, MM | 850nm | Most of the SFP/SFP+ MikroTik products | Works! |
| Fiberstore | SFP-10G31-40 | 40km | 10G | Dual LC, SM | 1310nm | CRS series, CCR series devices with SFP+ interfaces | Works! |
| Fiberstore | SFP-10G55-40 | 40km | 10G | Dual LC, SM | 1310nm | CRS series, CCR series devices with SFP+ interfaces | Works! |
| Fiberstore | SFP-10G32-40 | 40km | 10G | BiDi LC, SM | Tx:1330nm/Rx:1270nm | CRS series, CCR series devices with SFP+ interfaces | Works! |
| Fiberstore | SFP-10G23-40 | 40km | 10G | BiDi LC, SM | Tx:1270nm/Rx:1330nm | CRS series, CCR series devices with SFP+ interfaces | Works! |
| Optech | OPAK-TX1-00-C | 30m | 10G | RJ45 - Cat 6a/7 Cable | N/A | CCR, CCR, CSS series devices with SFP+ interfaces | Works, starting with v6.40rc20 RouterOS build. |
| ProLabs | SFP-10G-T-C | 30m | 10G | RJ45 - Cat 6a/7 Cable | N/A | CCR, CCR, CSS series devices with SFP+ interfaces | Works, starting with v6.40rc20 RouterOS build. |
U.2 Disks for RDS
The RDS2216-2XG-4S+4XS-2XQ supports U.2 SSD drives of any capacity, with a physical height limitation of 7mm. While any drive meeting this physical requirement should be supported, the following models has been verified:
- Samsung PM9A3
- Samsung PM983
- Micron 7300 series
- Micron 7400 series
- WD DC SN640
- Transcend UTE210T
- Innodisk 4TG2-P